Post by roninrun on Dec 6, 2015 19:20:20 GMT
Ok so I am ressurecting an old '86 FZ750 that I picked up for cheap (200 USD) and I've been slowly tearing her down and rebuilding pieces to get her back alive.
After pulling the tank and inspecting the carbs, I've been looking at the fuel lines that were already disconnected and I am struggling to figure where everything goes. I've reviewed the Clymer and I just can't put it together from diagrams and the instructions.
First, the underside of the air cleaner housing has 3 openings for hoses (at the top). All 3 of these are clogged on mine with what feels like rubber/plastic. I am not sure if I should remove these or if they are part of air cleaner housing. (see below)
The middle one goes to the crankcase ventilation hose which is simple. But mine did not have anything connected to the 2 vent hoses. I need someone to confirm where those 2 vent hoses go to from these openings on the housing.
Next is the carb, fuel tank, fuel filter, fuel pump connection. There are two tubes running from the carb (shown below). I have one short line coming from the petcock on the bottom of the fuel tank and and another small hose coming from the top of the tank near the lower mount.
The two hoses running from the carbs in the picture above go to nowhere. So I am not sure where they connect. The hose in the middle goes to the fuel pump (picture below).
Now you'll notice I am missing the fuel filter and the fuel filter bracket. Which I am assuming goes on the bracket screw on the bottom. However, once I put the fuel filter here ... I am not sure where the other end goes.
Can someone help me with the wiring as I don't have a solid diagram anywhere that shows me what connects to what. Below are the two diagrams I am using to help me understand this but it is quite confusing.
I can see that the tiny tube runs to the fuel filter but I am not sure if that can reach the bracket where the filter should be mounted. Just want to confirm. And if that is the case ... then where does the other end go?
And for the air hosing... it looks like there are two tubes going to a single filter (# 26) and out through hose (#31). Don't see any of these and not sure where they go to.
Anyone who can give me a map of how all this connects together will save me a lot of tinkering. Hope I've shown enough to get a good answer. Thanks!
After pulling the tank and inspecting the carbs, I've been looking at the fuel lines that were already disconnected and I am struggling to figure where everything goes. I've reviewed the Clymer and I just can't put it together from diagrams and the instructions.
First, the underside of the air cleaner housing has 3 openings for hoses (at the top). All 3 of these are clogged on mine with what feels like rubber/plastic. I am not sure if I should remove these or if they are part of air cleaner housing. (see below)
The middle one goes to the crankcase ventilation hose which is simple. But mine did not have anything connected to the 2 vent hoses. I need someone to confirm where those 2 vent hoses go to from these openings on the housing.
Next is the carb, fuel tank, fuel filter, fuel pump connection. There are two tubes running from the carb (shown below). I have one short line coming from the petcock on the bottom of the fuel tank and and another small hose coming from the top of the tank near the lower mount.
The two hoses running from the carbs in the picture above go to nowhere. So I am not sure where they connect. The hose in the middle goes to the fuel pump (picture below).
Now you'll notice I am missing the fuel filter and the fuel filter bracket. Which I am assuming goes on the bracket screw on the bottom. However, once I put the fuel filter here ... I am not sure where the other end goes.
Can someone help me with the wiring as I don't have a solid diagram anywhere that shows me what connects to what. Below are the two diagrams I am using to help me understand this but it is quite confusing.
I can see that the tiny tube runs to the fuel filter but I am not sure if that can reach the bracket where the filter should be mounted. Just want to confirm. And if that is the case ... then where does the other end go?
And for the air hosing... it looks like there are two tubes going to a single filter (# 26) and out through hose (#31). Don't see any of these and not sure where they go to.
Anyone who can give me a map of how all this connects together will save me a lot of tinkering. Hope I've shown enough to get a good answer. Thanks!